Call Today

 

Nearly everybody has their personal way of thinking with regards to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.

Installing a tub isn't exactly rocket science, however it does need solid plumbing, woodworking, as well as in some cases, tiling abilities. Changing an old bathtub with a brand-new one is additionally a moderately challenging job. If the old bathtub is readily accessible, the job can relocate speedily; if you have to open a wall to get rid of the old bathtub and also place the brand-new bath tub, the task is a lot harder. In either case, the job is within a house handyman's skills, although you will certainly require a helper to move out the old tub and set in the new one. Ensure you have qualified yourself for the job and are comfortable attempting it. As opposed to working with a contractor to take over a halfway-completed task, it is far better to think about utilizing one before you begin. Chances are you may require a specialist plumber to make tube connections.
This short article will aid you set up a new tub in your shower room if you have actually already bought a new tub and do not require to transform the plan of your previous supply of water pipelines.
Your devices and also material checklist need to make up the following:

 

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Blade


• Measuring tape


• Pipe Caps


 

Removing Old Taps

If you require to change old taps with brand-new ones as a part of your installment, after that the first thing you should do is detach the water. After doing so, turn on the taps to drain pipes any water staying in the system. The procedure of getting rid of the existing faucets can be quite problematic because of the restricted gain access to that is usually the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. When the supply pipes have been removed, utilize the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this process. Once the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any kind of old sealing compound.
Prior to proceeding to fit the new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new faucets to fit.

 

 

Fitting New Taps

If the tails of the brand-new faucets are plastic, then you will certainly need a plastic connector to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet and the other end supplies a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, position the tap in the placing opening in the bath/basin ensuring that the washing machines are in place between the faucet as well as the sink. Secure the faucet in place with the supplier supplied backnut. Once the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap ports. The former kind needs to be linked to the faucet finishes first, tightening just by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.

 

 

Installing the Bath tub

Utilizing the two wood boards under its feet, put the bathtub in the called for position. The wood boards are handy in uniformly spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 small factors.
The following objective is to guarantee that the bath tub is leveled all round. This can be accomplished by examining the level and adjusting the feet on the tub up until the level reviews degree.
To mount faucets, fit all-time low of the outermost adaptable faucet adapter to the suitable supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
Turn on the water supply and check all joints and brand-new pipework for leaks as well as tighten them if needed. Load the tub as well as likewise inspect the overflow electrical outlet and also the regular electrical outlet for leakages.
Lastly, fix the bath paneling as described in the manufacturer's user's manual. Tiling as well as securing around the tub must wait until the tub has been utilized at least once as this will certainly settle it right into its final setting.

 

 

Preparing for the Installment

Firstly, the supporting structure supplied with the bath must be fitted (if required) according to the producer's directions. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is essential to make sure that if the faucet features a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bath, it is additionally practical to fit a sustaining plate under the faucets unit to avoid pressure on the bathtub.
Fit the flexible tap adapters to the bottom of both faucets using 2 nuts and olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Make sure you make use of all of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom need to now be ready to be fitted in its final setting.

 

 

Tiling Around the Bath tub

In the location where the bathroom fulfills the tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate enough to break a stiff seal, triggering the water to permeate the wall surface in between the bath and the tiling, causing problems with moisture as well as possible leaks to the ceiling listed below.
You can choose from a variety of coloured sealers to assimilate your fixtures and also installations. They are marketed in tubes and also cartridges, as well as are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly load the bathtub with water before securing, to permit the activity experienced when the bathtub remains in use. The sealant can crack fairly very early if you do not think about this activity prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also conveniently offered on the marketplace. It is a good idea to fit the floor tiles utilizing water-resistant or water resistant glue as well as grout.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

I came across that blog entry about A Step-by-Step Guide to Installing a Bathtub while browsing the web. Enjoyed our piece of writing? Please share it. Help somebody else discover it. Thanks for your time. Visit again soon.

Avoid disaster, Call us!